Search Results

The research shows the experimental results for a free piston linear engine according to operation conditions of the linear engine and the structure of linear generator for generating electric power. The powerpack used in this paper consists of the two-stroke free piston linear engine, linear generators and air compressors. Each parameter of fuel input heat, equivalence ratio, spark timing delay, electrical resistance and air gap length were set up to identify the combustion characteristics and to examine the performance of linear engine. The linear engine was fueled with propane. In the course of all linear engine operations, intake air was inputted under the wide open throttle state. Air and fuel mass flow rate were varied by using mass flow controller and these were premixed by pre-mixing device. Subsequently, pre-mixture was directly supplied into each cylinder.

This work has been investigated the potential of in-cylinder EGR stratification for reducing the pressure rise rate of DME HCCI engines, and the coupling of both thermal stratification and fuel stratification. The numerical analyses were done by using five-zone version of CHEMKIN-II kinetics rate code, and kinetic mechanics for DME. The effects of inert components were used for the presence of EGR in calculation. Three cases of EGR stratification were tested on both thermal stratification and fuel stratification at the fixed initial temperature, pressure and fueling rate at BDC. In order to explore the appropriate stratification of EGR, EGR width was employed from zero to thirty percent. Firstly, EGR homogeneity case which means EGR width zero was examined. Secondly, EGR is located densely in hotter zone for combining with thermal stratification or in richer zone for a combination with fuel stratification. Lastly, the case was judged inversely with the second case.

This work experimentally investigates how the dwell time between pilot injection and main injection influences combustion characteristics and emissions (NOx, CO, THC and Smoke) in a single-cylinder DI diesel engine. Additionally, results from diesel injection are compared with those shown in dimethyl ether (DME) injection under the identical injection strategy to demonstrate the sensitivity of the combustion characteristics and emissions to changes of the fuel type. Two fuel injection systems are applied for this experiment due to the differences of fuel characteristic with regard to physical and chemical properties. The injection strategy is accomplished by varying the dwell time (10°CA, 16°CA and 22°CA) between injections at five main injection timings (-4°CA aTDC, -2°CA aTDC, TDC, 2°CA aTDC and 4°CA aTDC). It was found that pilot injection offers good potential to lower the heat-release rate with reduced pressure traces regardless of the dwell time between injections and fuel type.

In HCCI Engine, the HCCI combustion characteristics come under the influence of change of compression speed corresponding to the engine speed. The purpose of this study is to investigate mechanism of influence of engine speed on HCCI combustion characteristics by using numerical analysis. At first, the influence of engine speed was showed. And then, in order to clarify the mechanism of influence of engine speed, results of kinetic computations were analyzed to investigate the elementary reaction path for heat release at transient temperatures by using contribution matrix.

For the reduction of greenhouse gas emission in the transportation sector, various countermeasures against CO₂ emission have been taken. The eco-driving has been paid attention because of its immediate effect on the CO₂ reduction. Eco-driving is defined as a driving method with various driving techniques to save fuel economy. The eco-driving method has been promoted to the common drivers as well as the drivers of carriers. Additionally, there are many researches about improvement of fuel efficiency and CO₂ reduction. However, the eco-driving will have the reduction effect of CO₂ emission, the influence of the eco-driving on air pollutant emission such as NOx is not yet clear. In this study, the effect of the eco-driving on real-world emission has been analyzed using the diesel freight vehicle with the on-board measurement system.

Theoretically, homogeneous charge compression engines (HCCI) are able to grant a high thermal efficiency, as well as a low NOx and particulate emissions. This ability is mainly due to the combustion process, which, contrary to both Diesel and Gasoline engine, is homogeneous in time and space within the combustion chamber. But despite these advantages, the engine operating condition is limited by the narrow boundaries of misfire at low load and knocking at high load. For that matter, one of the numerous ways of overcoming knocking is to deliberately create fuel inhomogeneities within the combustion chamber, since it has proved to lengthen combustion duration and to drastically reduce maximum pressure rise rate (PRR). Nevertheless, though the global effects of fuel inhomogeneities on PRR have been studied, we lack information that explains this phenomenon.

In HCCI Engine, HCCI combustion characteristics come under the influence of change of compression speed corresponding to engine speed. The purpose of this study is to investigate mechanism of influence of engine speed on HCCI combustion characteristics by using numerical analysis. At first, the Influence of engine speed was showed. And then, In order to clarified the mechanism of influence of engine speed, results of kinetics computations were analyzed to investigate the elementary reaction path for heat release at transient temperatures by using contribution matrix.

Delaying CA50(Crank Angle of 50% Heat Release) of the HCCI engine to expansion stroke can lead to high indicated thermal efficiency as well as the avoidance of knocking. However, this method could induce the problem of cycle variability. In this study, the cycle-to-cycle variation of a HCCI engine fueled with DME was investigated. Experimental parameters of each cycle, such as in-cylinder temperature, pressure and gas flow rate, were recorded by fast response system, and analyzed consequently. Moreover, the interdependency between the combustion and the performance parameters were evaluated.

Thermal and mixing stratifications have been thought as one of the ways to avoid an excessive pressure rise on HCCI combustion. The purpose of this research is to investigate the potential of thermal and mixing stratifications for reducing PRR (Pressure Rise Rate) on HCCI combustion. The pre-mixture with thermal and mixing stratifications is charged in RCM (Rapid Compression Machine). After that, the pre-mixture is compressed and in that process, in-cylinder gas pressure and chemiluminescence images are obtained and analyzed. Furthermore, experimental results are compared with the computational results calculated by using multi-zone model for analyzing these mechanisms.

The HCCI engine is a next generation engine, with high efficiency and low emissions. However a rate of pressure rise is a major limitation for high load range. Recently, we are able to reduce the rate of pressure rise using thermal stratification. Nevertheless, this was insufficient to produce high power. Without the higher equivalent ratio, one way to improve the power is to increase the intake boost pressure. It is suggested that the rate of pressure rise is reduced by thermal stratification and the power is increased by boost pressure at the same time. The objective of this work is to understand the characteristics of combustion, knock and emissions for using both thermal stratification and the boost pressure. The calculations are performed by CHEMKIN and modified SENKIN. As a result of increasing the boost pressure, a higher IMEP was attained while the rate of pressure rise increased only slightly in the HCCI with thermal stratification.

The HCCI engine could offer low NOx, PM emissions and high efficiency. However the operation region of the HCCI combustion is limited because of the knocking at high load and the misfire at low load. Moreover the HCCI principle lacks direct combustion control and needs a system to control the combustion phasing with high accuracy. Today there exists various ways to control the HCCI combustion, such as Variable Valve Train, Variable Compression Ratio, Inlet Air Heating and Dual Fuels. However such variable mechanisms and Inlet Air Heating tend to be heavy and complex. Dual Fuels method needs two types of fuels and has a challenge in infrastructure. In this study, in order to develop a small and light HCCI engine, a simple HCCI combustion control system is proposed. DME (Di-methyl Ether) is used as the fuel to keep the structure small and light. In this system, the mixing ratio of three gases: stoichiometric pre-mixture, hot EGR gas and cold EGR gas is changed by only throttles.

A significant drawback to HCCI engines is the knocking caused by rapid increases in pressure. Such knocking limits the capacity for high-load operation. To solve this problem, thermal stratification in the combustion chamber has been suggested as possible solution. Thermal stratification has the potential to reduce the maximum value of the rate of pressure increase combustion by affecting the local combustion start time and extending the duration of combustion. The purpose of this study was to experimentally obtain fundamental knowledge about the effect of thermal stratification on the HCCI combustion process. Experiments were conducted in a rapid compression machine (RCM) equipped with a quartz window to provide optical access to the combustion chamber. The machine was fueled with DME, n-Butane, n-Heptane and iso-Octane, all of which are currently being investigated as alternative fuels and have different low temperature characteristics.

The Homogeneous Charge Compression Ignition (HCCI) engine is possible to achieve high thermal efficiency and low emissions. One of the main challenges with HCCI engines is structuring the systems to control combustion phasing, crank angle of 50% heat release (CA50), for keeping high thermal efficiency and avoiding an excessive rate of pressure rise which causes knocking, when operating conditions vary. Though some HCCI combustion control systems, for example Variable Valve Timing System and Variable Compression Ratio System, have been suggested, these control systems are complex and heavy. In this study, for the development of a lightweight and small-sized generator HCCI engine fuelled with Dimethyl Ether (DME) which is low-emission and easy to autoignite, a simple HCCI combustion control system is suggested, and the control system is evaluated experimentally.

The purpose of this study was to gain a better understanding of the effects of in-cylinder gas temperature stratification on reducing the pressure-rise rate in HCCI combustion. HCCI combustion was investigated using an optically accessible engine and direct visualization of the combustion chemiluminescence. The engine was fueled with Di-Methyl Ether. Computational work was conducted on the gas compression and expansion strokes in HCCI engine with simple 0-dimensinal multi-zones model. When fuel inhomogeneous charging in experiment, maximum heat release rate decreased. Combustion duration got longer. Maximum pressure-rise rate decreased. Chemiluminescence, of which transition was identified from the side of intake valve to the side of exhaust valve, was observed. It is need for total moderate heat release to get local moderate combustion with not overall but continuous combustion in chamber.

Homogeneous Charge Compression Ignition (HCCI) engine attracts much attention because of its high thermal efficiency and low NOx, PM emissions. On the other hand, Di-Methyl Ether (DME) is expected as one of alternative fuel for the internal combustion engines. In this study, four-stroke HCCI engine running on DME is developed to make it realistic application in production engines. This paper shows construction of the control method using both internal EGR at high temperature and external EGR at low temperature and estimates the performance of developed HCCI engine. Besides combustion characteristics of DME and the effects of EGR are researched with experiment and numerical calculation with elementary reactions. As a result, developed HCCI engine got comparable high thermal efficiency to conventional diesel engine but much lower Indicated Mean Effective Pressure (IMEP) than that. Meanwhile it can be said that DME is suitable fuel for the HCCI engines in combustion characteristics.

In order to clarify the reason why NOx emissions factor becomes higher at vehicle acceleration at intersections etc, two freight vehicles, that have EGR system for the reduction of NOx, were tested by an on-board NOx measurement system. Higher NOx emissions factor was observed in operations in lower-gear operation for each vehicle. Since the engine speed change was higher in the operation of lower gears, NOx emissions characteristics were analyzed in view of engine torque, NOx mass emissions and EGR rate, considering engine speed change. It was found that lower-gear operations made the engine speed change higher and the EGR rate lower. This seems to be one of the factors to engender the intensive NOx pollution at roadsides.

In this study, attention was paid to the method of mixing fuel to solve one of problems of the HCCI engine, which is the avoidance of knocking. The objectives of the work reported in this paper were to research the characteristics of HCCI combustion of the Methane/DME/air pre-mixture in the experiment and to check the oxidation reaction in two cases: when DME was used as an ignition accelerator for the Methane/air pre-picture, and when Hydrogen was used as ignition accelerator. Furthermore, from these results reference was made about basic specifications required fuel for an HCCI engine.

In the HCCI (Homogeneous Charge Compression Ignition) engine, a mixture of fuel and air is supplied to the cylinder and auto-ignition occurs resulting from compression. This method can expand the lean flammability limit, realizing smokeless combustion and also having the potential for realizing low NOx and high efficiency. The optimal ignition timing is necessary in order to keep high thermal efficiency. The Ignition in the HCCI engine largely depends on the chemical reaction between the fuel and the oxidizer. Physical methods in conventional engines cannot control it, so a chemical method is demanded. Combustion duration is maintained properly to avoid knocking. In addition, the amount of HC and CO emissions must be reduced. The objective of this study is to clarify the following through calculations with detailed chemical reactions and through experiment with the 2-stroke HCCI engine: the chemical reaction mechanism, and HC and CO emission mechanisms.

In the HCCI Engine, inhomogeneity in fuel distribution and temperature in the pre-mixture exists microscopically, and has the possibility of affecting the ignition and combustion process. In this study, the effect of charge inhomogeneity in fuel distribution on the HCCI combustion process was investigated. Two-dimensional images of the chemiluminescence were captured by using a framing camera with an optically accessible engine in order to understand the spatial distribution of the combustion. DME was used as a test fuel. By changing a device for mixing air and fuel in the intake manifold, inhomogeneity in fuel distribution in the pre-mixture was varied. The result shows that luminescence is observed in a very short time in a large part of the combustion chamber under the homogeneous condition, while luminescence appears locally with considerable time differences under the inhomogeneous condition.

The purpose of this research is to get fundamental knowledge and to experimentally understand about combustion characteristics of the fuel mixture. This paper shows the Homogeneous Charge Compression Ignition (HCCI) characteristics of a mixture of n-Heptane and iso-Octane in a rapid compression machine. The experimental matrixes cover the n-Heptane mixing ratios, rn-Heptane, ranging from 0 to 100vol% and the equivalence ratios ranging from 0.1 to 0.6. The experimental study on the effect of mixing fuels focuses on the low temperature oxidation reaction temperatures, TL, the high temperature oxidation reaction temperatures, TH, the low temperature oxidation reaction starting times, tL, the high temperature oxidation reaction starting times, tH, and the degeneration period. The results show that as rn-Heptane decreases, tL and tH become longer and TL and TH increase by 30K. As the equivalence ratio increases, tL becomes longer but tH is not a function of equivalence ratio.